H&R TRAK+ DR Wheel Spacers - 3mm 4x100/108 [06234571] – Euro Sport Accessories
Cart 0
H&R TRAK+ DR Wheel Spacers - 3mm 4x100/108 [06234571]

H&R TRAK+ DR Wheel Spacers - 3mm 4x100/108 [06234571]

SKU:
DR Series spacers fit between the wheel and hub, and require longer wheel bolts (ordered separately). Please verify bolt specifics before ordering (taper or round bolt head and shaft length).


Applications/Description
Make Model Chassis Years Bolt
Pattern		 Center
Bore		 Bolt/
Stud		 Thread
Type		 Width Notes
Audi 4000 Quattro Typ 85 1984-87 4/108 57.1 Bolt 14x1.5 3.0mm 3 28
Audi 90 Quattro 20V Coupe 1989-91 4/108 57.1 Bolt 14x1.5 3.0mm 3 28
Audi Quattro Turbo Coupe Typ 85 1983-85 4/108 57.1 Bolt 14x1.5 3.0mm 3 28
VW Cabriolet Golf I 1980-94 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Cabriolet Golf III 1995-03 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Corrado G60 1990-93 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Golf II 8V 1985-92 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Golf II 16V 1987-92 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Golf III 8V 1993-96 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Golf III 8V 1996-98 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Jetta I 1980-84 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Jetta II 8V 1985-92 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Jetta II 16V 1987-92 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Jetta III 8V 1993-96 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Jetta III 8V 1996-98 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Passat G60 Synchro 1989-94 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Rabbit 1980-84 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Scirocco I 1980-81 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Scirocco II 8V 1982-89 4/100 57.1 Bolt 12x1.5 3.0mm 3 28
VW Scirocco II 16V 1986-89 4/100 57.1 Bolt 12x1.5 3.0mm 3 28

HOW TO MEASURE

1. Gather Tools

To properly measure your wheel gap you will need a few simple tools:

  • Measuring device with millimeter units
  • Straight edge--Yard stick or similar

2. Check Your Gap

  1. Place a straight edge flush with the face of the wheel and tire combination. Make sure the straight edge touches the tire in two spots to keep the straight edge even with the tire.
  2. Use the measuring device to measure from the inside of the straight edge to the inner fender lip. (see diagram)
  3. Make sure that the measurement is taken at the point where the wheel and tire is closest to the fender. For instance, on a car with a large amount of negative camber the tire and wheel may be closest at the front or rear edge of the fender.